Описание

MP-15RM Пластик магнитный привод насоса 220 В 50/60 Гц

MP-15RM Food Grade Plastic Magnetic Drive Pump 220V 60HZ

Introduction:

1. MP magnetic pump is manufactured by RONDA is compact structure, small volume, light weight.

2. Pump is widely used in all industries works as booster pump, chemical, lab pump, circulation pump.

3. Pump is designed with 50 or 60Hz to meet requirements of clients from different countries.

4. Pump is generally designed for no shaft seal, completely avoids defects of pollution after corrosion caused by liquid leakage, which exists in traditional mechanical shaft seal pump, it is the optimum liquid transport pump.

5.Normal operating temperature is 0-80°C. If the higher operating environments is required, please consult with us.

PARAMETER DATA:

Model	tube interface		thread interface		Max. Flow	Max. Head	Standard capaicty		medium density	Power	Voltage
	Inlet	OutLet	Inlet&Outlet	Tube	Max. Flow	Max. Head	Flow	Head	medium density	Power	Voltage
	(mm)	(mm)	(inch)	(mm)	(L/min)	(m)	(L/min)	(m)	(g/cm^3)	(W)	(V)
MP-15R	16	16	-	-	16	2.7	8	1.5	<1.3	10	220
MP-15RM	-	-	0.75	13	16	2.4	8	1.5	<1.3	10	220

installation and operation of magnetic pump

1. Magnetic pump should be horizontally installed, but not upright. Plastic pump is not able to endure the weight of pipeline. In case of special occasions requiring upright installation, motor should be kept upward.

2. When liquid level is higher than the centerline of pump, turn on the valve of intake pipe before start; when liquid level is lower than the centerline, a bottom valve should be fitted to the pipeline.

3. Check before operation to make sure that motor rotates flexibly without jamming and abnormal sound, and that all fasteners are not loosened.
4. Check whether motor rotor in accordance with the direction sign.
5. After motor is started, slowly turn on discharge valve, when pump enters normal working state, adjust the discharge valve to the requiring opening.

6. Before pump stops working, turn off discharge valve first, and then the valve of intake pipe.

NOTE:

SHIPPING:

THE BUYER IS RESPONSIBLE FOR ALL SHIPPING & HANDLING COSTS. SHIPPING COSTS ARE DETERMINED BY THE LOCATION OF THE BUYER AND THE WEIGHT OF THE ITEM SOLD.

SHIPPING WILL NOT TAKE PLACE UNTIL PAYMENT IS RECEIVED.

ATTENTION INTERNATIONAL BUYERS: PLEASE PROVIDE A PHONE NUMBER AND SHIPPING ADDRESS SO WE CAN GET THE ITEM SHIPPED TO YOU. DO NOT FORGET ABOUT ANY OTHER

CHARGES WHICH ARE CHARGED BY THE CARRIER. THIS IS SOMETHING WE HAVE NO CONTROL OVER AND IS AN ADDITIONAL CHARGE TO SHIPPING.

RETURN POLICY:

WE WILL REFUND YOUR MONEY IF THE ITEM YOU RECEIVE DOESN'T WORK AT ALL UNLESS IT WAS LISTED AS BEING "PARTS ONLY" OR "NOT IN WORKING CONDITION."

THE BUYER WILL BE RESPONSIBLE FOR ALL RETURN SHIPPING FEES. ONCE THE ITEM IS RECEIVED AT OUR LOCATION WE WILL ISSUE THE REFUND.

ITEMS MUST BE RETURNED WITHIN 14 DAYS FROM THE DATE IT WAS DELIVERED TO THE BUYER.

ADDITIONAL INFORMATION:

CUSTOMER SATISFACTION IS VERY IMPORTANT TO US. PLEASE FEEL FREE TO SEND US AN EMAIL OR A MESSAGE THROUGH ALIESPRESS WITH ANY QUESTIONS, COMMENTS, OR CONCERNS.

BUYERS: CHECK OUR FEEDBACK AND BID WITH CONFIDENCE. WE WILL NOT LEAVE FEEDBACK FOR BUYERS UNTIL WE RECEIVE FEEDBACK. SHOULD A PROBLEM ARISE PLEASE CONTACT

US BEFORE LEAVING NEUTRAL OR NEGATIVE FEEDBACK; THIS WILL ALLOW US TO WORK WITH THE BUYER TO RESOLVE ANY PROBLEMS.

BE SURE TO ADD US TO YOUR FAVORITES LIST AND CHECK OUT OUR OTHER ITEMS!

MP-15RM Пластик магнитный привод насоса 220 В 50/60 Гц